丁基钢板腻子橡胶止水带价格

丁基钢板腻子橡胶止水带价格

丁基钢板橡胶腻子止水带是近几年地铁工程应用最为广泛的一种橡胶止水带，外观为塑料布包裹，目的是防止橡胶腻子在运输移动中被污染，腻子内为1毫米厚的镀锌钢板。钢板腻子止水带为综合性能优良的高分子材料与镀锌板复合而成的止水产品。
The butyl steel plate rubber putty waterstop is the most widely used rubber sealing belt in Subway Engineering in recent years. Its appearance is wrapped with plastic cloth, the purpose is to prevent the rubber putty from being polluted in transportation and transportation, and the 1 mm thick galvanized steel plate inside the putty. The steel plate putty water stop belt is a water stop product composed of high polymer material and galvanized sheet.
橡塑腻子主体材料为耐老化性能优良的橡塑材料，具有特强的自粘性；夏季高温不流淌。冬季低温不发脆；并具有优异的耐水、耐酸碱和耐老化性能；使用寿命长，产品本身无毒，环境良好。为了承受一定的弯曲和压力。中间来有0.4或0.6mm的钢板。该产品对建筑缝之间提供可靠的防水、防渗功能。
The main material of rubber and plastic putty is a rubber and plastic material with excellent aging resistance. It has a strong self viscosity, and it does not flow at high temperature in summer. In winter, the low temperature is not brittle; it has excellent water resistance, acid and alkali resistance and aging resistance; long life, the product itself is non-toxic, and the environment is good. To bear a certain amount of bending and pressure. There are 0.4 or 0.6mm steel plates in the middle. The product provides reliable waterproof and anti-seepage function between construction joints.
丁基腻子钢板橡胶止水带系列产品包括各种规格型号的产品，并可根据用户要求，生产各种非标型号的产品，满足工程上的实际需要。
Ding Ji series of putty steel and rubber water stop products include all kinds of specifications and products, and can produce all kinds of non-standard products according to users' requirements, so as to meet the actual needs of engineering.
丁基腻子钢板橡胶止水带主要应用范围：
The main application range of Ding Ji putty steel plate rubber sealing belt is:

丁基钢板腻子橡胶止水带价格
隧道、地铁、堤坝、涵洞、水利水电工程中施工缝、高层建筑地下室、地下停车场等主要工程施工缝。
The construction joints such as tunnel, subway, dam, culvert, construction seam in water conservancy and hydropower project, basement of high rise building, underground parking lot and other main construction joints.
钢板橡胶腻子止水带安装：
Steel plate rubber putty water stop belt installation:
将丁基腻子钢板橡胶止水带连接处搭接100mm，用手压紧排除空气靠其自身粘接牢固，并加固轧丝后重新贴上保护膜。钢板腻子止水带安放在墙体的中间位置，用铁丝固定在钢筋上，止水带略高于混凝土介面。第一次浇注前，将钢板腻子止水带下端的保护膜取掉，混凝土浇注至钢板腻子宽度的1213处，在二次浇注前将上端保护膜取掉，再进行浇注。
The butyl putty steel and rubber sealing belt connection is overlapped with 100mm. The air is compressed by hand and the air is firmly adhered to itself, and the protective film is re attached after strengthening the wire. The steel plate putty water stop belt is placed in the middle of the wall, and the wire is fixed on the steel bar with iron wire. The water stop belt is slightly higher than the concrete interface. Before the first pouring, the protective film on the lower end of the steel plate putty water stop is removed, and the concrete is poured to 1213 parts of the width of the steel plate putty. Before the two casting, the upper end protective film is removed and poured again.
钢板腻子止水带施工与安装注意事项：
Construction and installation of steel plate putty water stop belt:
采用钢筋或模板对钢板腻子止水带进行定位。施工缝间隙止水带一般一半先浇注于砼中，另一半在二期施工中埋入砼内。因此，钢板腻子止水带固定方法必须可靠，避免发生移位。二期施工前，另一半止水带应注意保护。浇注混凝土。在浇注过程中应注意捣浇压力和方法，以避免砼中尖角石子和锐利的钢筋刺破钢板腻子止水带。
The steel or the formwork is used to locate the water stop belt of the steel putty. Half of the water belt in the gap between the construction joints is first poured into the concrete, and the other half is embedded in the concrete in the two phase of the construction. Therefore, the fixing method of the steel plate putty water stop belt must be reliable and avoid the displacement. Before the two phase of construction, the other half of the water stop should pay attention to protection. Cast concrete. In the pouring process, we should pay attention to the pressure and method of Ramming in order to avoid the sharp stones in the concrete and sharp reinforcing bars to pierce the water stop belt of the steel putty.